Backbuttering mosaicsSometimes I  get asked how to backbutter mosaic tiles. I constantly have to tell people that you really don’t need to. There are very few instances when you’ll need to backbutter a mosaic tile. Normally if you feel the need to backbutter mosaics it is easier to simply use a larger trowel on your substrate.  

[continue reading…]

laticrete_linear_drainThe wonderful folks at Laticrete sent me a linear drain to play with. And you know me – I bastardized it until it was virtually unrecognizable, ran it through the paces and did things you really shouldn’t do with nice, high-end products like this.

And it survived. Word on the street is that they read my blog, probably for comic relief and to instruct people what NOT to do with their products. So I’m sure they knew this when they sent it… I mean honestly, I soaked their grout in cherry Kool-aid for a week, how could they NOT know?

I did, however, put it to good use in a very cool shower. This is a brief overview of the installation of that drain.

[continue reading…]

In the first part of this tutorial I showed you how to frame up your access panel and get the magnetic latches on it and all lined up. So right now you should have an access panel in the side of your fancy-pants tub and a box of tile just sitting there and laughing at you. If you don’t have that check out the link above. I’ll wait. :whistle:

That post is the meat and potatoes of building your access panel. This one simply describes the basics of installing your tile as well as placing an insert, if need be, into the access panel.

The biggest thing you’ll need to pay attention to as you install your tile is the perimeter of your access panel. You don’t want to get thinset into it or otherwise block it. If you do – it simply becomes a wall with a lot of pieces.

[continue reading…]

Finished tiled shower ceilingMichael has recently pointed out (a bit more eloquently than I would have) that I have indeed been a lazy bastard and have not yet written this post. Apparently people actually want to know how to do stuff I do – weird, right? So here you go – making your ceiling shiny.

The main problem people have with tiling a ceiling is getting the tile to stay where they put it. Believe me, I’ve had more than one tile fall on my noggin before I figured out what works. Since I’m relatively certain you aren’t very interested in what doesn’t work I’ll tell you what does, it saves headaches – literally.

You do not need a $75 bag of non-sag thinset to tile a ceiling. Non-sag thinset is basically just thinset that is sticky – it’s great stuff! It’s also expensive stuff. You can accomplish the same with the $15 bag of regular modified thinset.

Before you start hanging head-bashers (ceiling tile) you should, as always, have the substrate properly prepared. They do not always need to be waterproof. It’s a good idea and never hurts, but it isn’t always necessary. The photos of the shower I have here was in a small bathroom with limited ventilation so I waterproofed the ceiling as well.

[continue reading…]

Yup.

End of post.

Fine, I’ll elaborate . . .

To understand this you should understand what designates a particular tile as a ‘floor’ tile. A couple of different things determine this including the PEI Rating and Static Coefficient of Friction (that’s just fancy ass talk for how slippery a tile’s surface is).

[continue reading…]

Which tile to choose depends mostly upon where you plan to install it and, of course, whether or not is has the look you want for that specific application.For the former I will explain several things to take into consideration. The latter is entirely up to you (unless you’re the husband, in which case it’s up to your wife). So before you choose your tile you need to consider a couple of things.

Where are you installing the tile?

If it will be installed on a wall in a non-wet area, you do not need to worry about much except whether or not you like the way it looks. A non-wet area is defined as an area that is not regularly exposed to a significant amount of water. Wainscots, backsplashes, and fireplaces are examples on non-wet areas.

If it will be installed in a wet area, such as a shower, you need to take into consideration the absorption rate of the tile to an extent. Although it is not that dire to consider this, the lower the percentage of absorption, the better it will be for your application.

You can install travertine in a shower but porcelain will be easier to take care of. An application such as a steam shower or exterior patio would suggest a lower absorption rate. A good rule of thumb is the higher the chance of exposure to moisture and temperature, the lower the absorption rate you want.

If the tile will be installed on a floor you will also want to consider what is called the Static Coefficient of Friction. That’s just a big phrase to describe how slippery a tile is.

This number will (usually) be below one.  Just consider this number to be between 1 and 10. For instance, consider a SCOF (Static Coefficient of Friction) or COF of 0.5 to be a 5. This is the number which most standards consider “slip resistant”.The higher the number, the less slippery it will be.

Tile will have two COF numbers – one for wet and one for dry. You may want to consider both numbers for an application such as a bathroom or shower floor or a patio. Consider a 1 (0.1) to be akin to ice and a 10 (1.0) to be sandpaper.

Other factors to take into consideration include the size of the tile as well as the size of the grout lines (to a smaller degree).  If you have 2 inch by 2 inch tile with fairly large grout lines, such as a shower floor mosaic,  it will have more friction than 18 X 18 inch tiles with 1/16 grout lines. The grout lines add friction because they are uneven and break up the flat, continuous surface of the tile.

[continue reading…]