I constantly reiterate the need for a tile installation to be flat. Not necessarily level, but always flat. This is the mark of a true professional and the thing that turns an ‘okay’ installation into a spectacular installation. (Did I just type ‘spectacular? Jesus…) Anyway, the method I use on floor tile to get it flat is fairly simple and ensures that each tile is the exact same height as the tiles surrounding it.

Before I show you that you need to understand, as always, that the substrate preparation is the most important aspect of this. If your tile substrate looks like a skate park you’re never going to get a flat tile installation over the top of it. Your substrate needs to be as flat as you can possibly get it. Take time with your preparation – it makes the rest of the installation run smoothly and gives you a solid foundation.

Start by getting a few tiles set and make sure they are all flat with your straight-edge, just place the straight-edge on top of the set tiles and ensure that there are no open spaces beneath it and that every tile is the same height. You can push down on tiles that may be a bit high or take a tile up and place a little more thinset beneath it to raise it some. Once you have that correct the rest is cake, baby! (You ever seen a cake baby? They’re messy…)

All these photos are of a travertine tile bathroom floor. I used travertine photos because it happens to be one of the least dense stones and usually have quite a few pits and open spaces in the stone itself. If the tile is ‘filled’ travertine, as this is, it is normally only filled from the front so that, once installed, it has no open areas or pits on the face of the tile. You can, however, see these open areas in the back of the tile. I’m gonna show you how to fix this, too. You get a two for one with this post.

Photo 1

Once you have the initial couple of tiles set, as in photo 1, just comb your thinset onto your substrate in a uniform direction. (Make all the little lines from the trowel go the same way) This eliminates the possibility of trapping air beneath your tile and leaving spots that are not fully adhered (hollow spots). If you make the pretty little swirlies they may look cool, but they can also trap air beneath your tile. On a side note: my spell-check just told me that ‘swirlies’ isn’t a word – so I’m makin’ it one.

In photo 2 you can see the back of the travertine tile. See how it has all those pits and crevices and empty spots? You’ll want to fill those up with thinset to give the tile a good, solid fill and, essentially, make it more dense and durable. Do this by using the flat side of your trowel (Photo 3) and scraping thinset along the back of the tile in every direction. This ensures it is completely full and there are no open areas left. (Photo 4)

Photo 2

Photo 3

Photo 4

-This is what is called ‘backbuttering’ your tile. You’ll more than likely run into that term a lot when researching tile – that’s all it is. For an installation where you have an inconsistent tile or a questionable substrate you can always do this, then flip your trowel around and comb thinset on the tile as well (make pretty little lines – not swirlies!)

Now that you have a good solid piece of shiny rock to put down on your floor, flip it over and put it there. Make sure you flip it over – shiny side up. When you place it in the thinset on the floor place it directly against the two tiles adjacent to it (Photo 5) so that two sides of the tile are actually touching the two tiles next to it. As you do this you can push the tile down to just the right height to be flush with the tiles next to it.

Photo 5

This will ensure that the tile you just put down is the same height as the surrounding tiles. You can take your straight-edge again and use it to push the tile down and get it to the same height. If your tile goes down too far – PULL IT UP! and put a little bit more thinset beneath it.

I yelled ‘PULL IT UP’ because for some reason people think that once the tile is down – that’s it. It can’t be moved. That’s not it. Until the thinset cures – tomorrow! – that tile can be moved, pulled up, adjusted, smashed, replaced, etc. Do not be afraid to pull it back up and put more thinset beneath it if it sets too low.

Photo 6

After you get the tile at the proper height, and this needs to be along both edges that are touching, then you can go ahead and pull it away from the two tiles to create your grout line and make sure you are, indeed, at the proper height. (Photo 6)

Then just insert your spacers and make sure it is in the correct place. (Photo 7) Pulling it back also ensures that there is full coverage between the thinset and the back of your tile. Remember those little ridges that the trowel created? The ones that were not fully squished down as you were adjusting your tile will be pulled slightly as you create your grout line and this will create full coverage and support beneath your tile.

Photo 7

Photo 8

-You can take your straight-edge and lay it across the tile to ensure that they are all perfectly flat. (Photo 8 ) If one sets a little bit high you can simply wiggle the straight-edge back and forth until it is flush. If it sets a little too low – PULL IT UP! (damnit) and do it again.

It may seem like a tedious process – it is. But when done correctly you end up with a totally flat, professional looking tile installation which will last for years.

See:

If you would like to receive little bite-sized pieces of my wealth of useless tile wisdom sign up for TileTips. You will receive a short (it’s short – I hate long emails) little email with tips, tricks and secrets (and bad humor) all wrapped up in one shiny little package. You will get one or two a week (depending on my drinking schedule) and they will help you set tile like a pro. Or, if you’re a pro, they’ll make your job sooooooo much easier – and make you rich and famous.

Before installing tile on your floor you must make sure your floor is properly prepared.  A properly prepared floor does not have to be level. It must, however, be flat.

The only time the levelness (is that a word?) must be taken into consideration is when drainage is an issue, such as on a porch or in a shower. In those cases you must make sure your floor is not level – it has to be angled toward a drainage area.

If your floor will not be subjected to water regularly, such as a kitchen or bathroom floor, it does not necessarily have to be level. That does not mean you can have a 45 degree angle from your door to the cabinet (although I suppose you could if you wanted), it just means if your floor is not absolutely level it will not negatively affect your tile installation.

One of the things you must make sure of, among other things, is that your floor is flat. If it is not it will be difficult to set your tiles without what we call “lippage”. That’s a ridiculous word, isn’t it? Lippage simply describes the difference in the height of two adjacent tiles. If you have a tile that sticks up higher than the tile next to it you have lippage. You don’t want that. Starting with a flat floor helps prevent it.

When prepping your floor for tile trade your level for a straight edge. Don’t be concerned with how level your floor is, be concerned with how flat it is.