When using Kerdi for your shower floor you need to make a hole in it for the drain. If you don’t then you simply have a shallow swimming pool rather than a shower. This hole must be the exact size and it must be in the correct spot. There are two ways to do this.

The first way is to install your membrane on the floor then cut out your hole for the drain. While this method works, I’m not a fan. It leaves open the possibility of cutting more than just your membrane (where it needs to be cut), slipping and damaging the drain or messing up the bond of the membrane around the drain where you need it to be bonded (accidentally debonding a portion of the membrane while you’re cutting the hole).

It works, but there’s a better way. I’m assuming here that you’ve already cut your hole in the floor, installed the drain and mud deck and cut your kerdi membrane to the correct size for your floor – the width of your floor plus four inches, by the length of your floor plus four inches. That is your floor size plus two inches up each wall. Got that? Good, let’s move on.

In your Kerdi drain box there are two templates. One is for the hole in your subfloor, so the drain fits down into it correctly (it says cut-out template for floor), and one for the membrane (it says cut-out template for kerdi membrane). Grab the one for the kerdi membrane – I’m assuming you already have the hole cut out in the floor, yes? If not you’re doing it wrong… Remove the inner circle – this is the part you’ll be using.

Set the template (the circle) into the center of your drain. It will fit perfectly into the center depression of the Kerdi drain. Measure your shower floor in each direction to the center of the template, the little cross, plus two inches. For instance: if your shower is 36″ deep x 48″ wide and your drain is centered then distance to the cross should be 20″ from the back (18″ plus 2″) and 26″ to the side (24″ plus 2″). Write those numbers on your template in the appropriate spots – 20″ at the top of the cross (to the back wall) and 26″ on the side of the cross (to the side wall).

You can click on any of these photos to see a full-size version.

Marking the center of your drain

Marking the center of your drain

Now take your Kerdi membrane and lay it out in the same orientation in which it will be in the shower. Measure 20″ from what will be the back of the shower and make a mark, then measure 26″ from what will be the side and make another mark. You should have a cross on your membrane similar to the one on the template. That is the center of your drain in the shower.

Now take your pen and place the tip right in the center of the cross. Gently push the tip of your pen through the template so it pokes out the back of the template like this:

 

pen tip placementPush pen tip through to the other side

Once you’ve done that fold the template back so you can see the pen tip and place it directly onto the little cross you made in the membrane. Then hold it firmly in place so it doesn’t move and remove the pen (Do this with the other hand also unless you’re taking pictures too).

centering the template on the membraneRemove pen from template

Tracing the template onto the membraneNow just trace around the outside of the template onto your membrane.

 

 

 

 

Cutout markings on kerdi membraneOnce you’re done with this you should have a perfect circle on your membrane in the exact spot as your drain in your shower.

 

 

 

Cutting out the drain circle

Now take your razor knife, scissors, bowie knife, whatever, and cut the circle out of your membrane – take your time! It needs to be exact and there are no second chances if you slip.

 

 

 

Completed drain cut outThat’s it. Now you have your drain cut out of your kerdi membrane in the correct location.

 

 

 

Now you can lay it into your shower floor and everything will line up correctly without any problems. I normally roll it up from each end to the center so when I lay it into the shower floor I place the cutout directly over the drain and roll the membrane out from the drain in each direction. That way you ensure it’s in the correct spot.

Completed shower floor with Kerdi membrane

Although this sounds like an extremely long process because there are a lot of words on this page, it’s actually quick and straight-forward. If you use this method you eliminate the possibility of damaging your membrane and you end up with a hole where you need it and the size you need it.

Oh, and if you actually cut it out with a bowie knife – send a picture. I gotta see that! :D

{ 69 comments… add one }

Leave a Comment

Cancel reply

  • Matt

    Hi Roger,

    I’ve been installing the full get up of the Schluter shower system for a bath remodel I’m doing. To start, I had a drain that was not accessible from below and followed the Schluter instructions for installing the drain flange and shower tray. As I am working on getting the Kerdi membrane ready for the pan, I noticed a portion of the flange has some movement and isn’t completely bonded. The section is about a 5”x2” area. Am I going to need to chip this all out and reset the drain or is there a way I can correct this without taking out everything?

    • Roger

      Hi Matt,

      The flange will not bond with thinset. The way it ‘bonds’ is that the little dovetailed cutouts around the perimeter are locked in using thinset. The thinset bonds to the foam below, and the thinset bonding the kerdi above bonds to the thinset through the cutouts. This locks the drain into place.

      • Matt

        So just to be clear, I’m good. I don’t want to membrane the pan and tile only to have a “soft” or flex in the floor to cause the grout to crack.

        • Roger

          Should be, yes.

  • Rebecca Szanyi

    DEAR (for all the help us give is DIYer’s) Rodger, Is it totally necessary to use the Kerdi drain? For our steam shower could we use a conventional drain, already installed in a mud pan, using Kerdi membrane & Kerdi Fix (or silicone?), then tile? Our home is built on concrete floor.

    • Roger

      Hi Rebecca,

      No, but you need to either use a topical drain of some sort or (with a regular drain like you have) utilize the ‘divot method’. You can google that or I will have a post tomorrow about it.

  • Neil Mumby

    Hi Floor Elf – I have purchased your EBook on Kerdi Shower installation, with a view to doing that in my home country of NZ. This brings a lot of challenges because knowledge of Kerdi products appear limited here, due to most installers favouring paint on topical water proofing methods. As a consequence associated install materials are also limited. It looks like the only unmodified thin set I can obtain here is laticrete 211 and the closest to floor mud is laticrete 3701. In your opinion are these adequate for installing (say) 16 x 16 inch ceramic tile on floor and walls in a curb less walk in shower with kerdi line drain? Any guidance appreciated.

    • Roger

      Hi Neil,

      I honetly don’t know. The product numbers are completely different there, so I have no idea which products those are comparable to. The 3701 appears to be a modified. However, if it is laticrete you shouldn’t have any issues with either, as I have not seen any of their products which are sub-par for an installation of that type. You may want to give Laticrete’s tech line a call or email and ask them, they’ll have knowledge of those specific products, I don’t even have access to them.

  • Quentin

    Roger,
    Thanks to you for taking the time to do what you are doing here. It is greatly appreciated by many.
    I left a question on the “message” thingy on your FB page. Is it best to place questions here, should I do the question over here, or is it okay as is?

    Thanks again!

    • Roger

      Hi Quentin,

      You can ask it anywhere, I answer them all. I usually do facebook last.